
Dandenong Custom Cabinets handles cabinet refacing & doors Dandenong kitchens are often better served by than a full rebuild, replacing doors, drawer fronts, panels and hardware on carcasses that are still sound. Refacing makes sense where the boxes are square and dry and the layout still works, which describes a surprising number of kitchens in the local post-war housing stock. Where the carcasses are swollen at the sink run or the layout has stopped functioning, the honest answer is replacement, and the assessment says so rather than selling the cheaper job regardless. New fronts are made to measure in melamine, high-pressure laminate, timber veneer or sprayed two-pac polyurethane, with soft-close hinges and full-extension runners fitted as standard. Twelve years of south-east Melbourne work and $20 million in public liability cover sit behind every job. Call 0440 132 026 for a free assessment and quote.
GET A FREE QUOTE
Dandenong Custom Cabinets
A reface replaces every surface that is seen and every moving part: doors, drawer fronts, exposed end panels, kickboards, handles, hinges and drawer runners. The carcasses, the benchtop and the plumbing stay where they are, which is what removes most of the cost and most of the disruption.
The boxes, the internal shelves and the existing layout remain. That is the trade-off worth being clear about: refacing changes how a kitchen looks and how it operates, but it cannot move a sink, widen a walkway or convert cupboards into drawer banks beyond what the existing openings allow.
Replacing only the doors and hardware, keeping the existing fronts elsewhere, suits a kitchen where the fronts have worn unevenly. Adding a new benchtop to a reface is common and often the single biggest visual change, templated after the new fronts are fitted.
Dandenong Custom Cabinets
A kitchen is the most common reface because it has the most doors and takes the most wear. The usual sequence is an assessment, a measure of every opening, fabrication of the new fronts in the workshop, then a one to two day install that keeps the kitchen usable for most of it.
Kitchens from the 1990s and 2000s are the strongest candidates, including the renovated post-war homes off Cheltenham Road and around Thomas Street where an earlier owner replaced the kitchen once already, because the carcasses are generally sound and the layout is usually still sensible while the doors have dated badly. A kitchen whose only real problem is tired melamine doors and failing hinges is the textbook case.
Converting a lower cupboard into a bank of drawers is possible within the existing opening, and it is the upgrade that most changes how a kitchen works day to day. Soft-close runners rated to around 40kg are fitted as standard, which is usually a step up from what the original kitchen had. Where more than this is needed, a full custom kitchen is the better spend.
Dandenong Custom Cabinets
New doors and drawer fronts can be ordered to the measured openings alone, without any other work, which is the cheapest route to a changed kitchen. Every opening is measured individually rather than assumed consistent, because original cabinetry rarely repeats exactly across a run.
Melamine and high-pressure laminate are the value choices and handle daily wear well. Timber veneer gives real grain across the fronts, with grain direction specified at the drawing stage. Sprayed two-pac polyurethane gives the deepest finish and can be colour-matched to an existing benchtop or splashback, which is often the deciding factor when only the fronts are changing.
Profiles run from flat slab through shaker to handleless J-pull and finger-pull. Switching to a handleless profile changes the look more than a colour change does, though it requires the door edge detail to suit. Handles are a cheap, high-impact change and can be swapped independently of everything else.
Dandenong Custom Cabinets
Not every tired cabinet needs a new front. A door that sags, binds or no longer closes is usually a hinge problem rather than a door problem, and rehanging on new three-way adjustable hinges fixes it for a fraction of a reface. Chipped edges and lifting edge-banding can be re-banded where the substrate underneath is sound.
Replacing hinges and runners alone transforms how a kitchen feels to use. Soft-close hinges rated beyond 100,000 cycles and full-extension soft-close runners rated to around 40kg mean drawers pull out completely and doors stop slamming, and both can be retrofitted to sound carcasses. This is the single best value upgrade available to a kitchen that otherwise looks fine.
Repairs extend to display cabinets, dressers and freestanding units, covering loose joints, failed runners, broken hinges and damaged backs. Where a piece has sentimental or furniture value, repair is almost always the better answer than replacement.
Dandenong Custom Cabinets
Four things decide whether a carcass can be refaced: whether the box is still square, whether the board is dry and sound especially at the sink and dishwasher, whether the fixings into the wall and floor are solid, and whether the openings are consistent enough for new fronts to sit with even reveals. Any swelling at a sink-run base unit is the usual disqualifier, because a new door on a swollen box will not hang true.
A reface that goes wrong almost always does so because the carcass was not sound to begin with. New fronts on a box that has dropped or swollen will show uneven reveals within months, and no amount of hinge adjustment corrects a carcass that is out of square.
Where the assessment finds the boxes unsound or the layout genuinely not working, replacement is recommended even though it is the larger job. The nearest long-run Bureau of Meteorology station, Moorabbin Airport (086077), records October as the wettest month at about 59mm and July daytime highs near 13°C, and in that temperate, damp-winter range an unsealed carcass at a sink run deteriorates quietly over years, so the sink cabinet is always checked first.
Dandenong Custom Cabinets
Refacing suits the Dandenong housing stock unusually well. The suburb recorded 30,127 residents at the 2021 Census with a median weekly household income of about $1,267, a median weekly rent of about $319 and a high proportion of renters, so a job at under half the cost of a replacement is often the difference between doing the work and deferring it. For investors and landlords a reface turns a dated kitchen around between tenancies without the time or expense of a rebuild. The 1990s and 2000s kitchens across the newer parts of Greater Dandenong are precisely the vintage where carcasses are sound and doors are not. Dandenong Custom Cabinets gives the assessment straight, including when replacement is the better spend, carries $20 million in public liability cover, and keeps the same team across assessment, fabrication and install.
Dandenong Custom Cabinets
Refacing is quoted on the number of doors and drawers, the finish and any hardware upgrades, so the figures below are indicative guides rather than a quote. A modest kitchen reface in melamine or high-pressure laminate, covering new doors, fronts, handles, hinges and runners, often runs from around $4,000 to $8,000, comfortably less than half a comparable full replacement. Timber veneer fronts typically lift that to roughly $7,000 to $14,000 depending on kitchen size. Sprayed two-pac polyurethane generally sits around $8,000 to $18,000 for a full kitchen, still well under a from-scratch custom kitchen. Doors and drawer fronts supplied alone, without hardware or installation, are the cheapest option and are quoted per opening. Hardware-only upgrades, rehanging on soft-close hinges and fitting full-extension runners, are the lowest-cost improvement available and are quoted per door and drawer. An itemised written quote follows the free assessment. Call 0440 132 026 to book one.
Dandenong Custom Cabinets
Three options compete for the same kitchen, and the right one depends on the carcasses rather than the budget. Refacing keeps sound boxes and replaces everything seen, at under half the cost of replacement and with one to two days of disruption instead of weeks. It cannot move a sink, widen a walkway or change the layout. Flat-pack replacement, bought at IKEA on Princes Highway, Springvale or at Bunnings, buys a new layout cheaply but in fixed cabinet sizes, so in a settled home the filler panels multiply and the install, levelling and stone coordination fall to the buyer. A full custom rebuild changes the layout, the storage and the plumbing, scribed to the real walls, and costs the most while lasting longest. The decision rule is straightforward: sound carcasses and a workable layout favour refacing; a layout that has stopped working favours a rebuild; a square, modern room on a tight budget is where flat-pack competes. Refacing also extends past kitchens, to vanity doors and fronts and to robe fronts, and a reface is frequently paired with a new benchtop templated after the fronts are fitted. Where the assessment finds the boxes unsound, the recommendation will be replacement, because new fronts on a failing carcass waste the money twice.

It starts with a proper site measure, not a guess. We come to your home or premises anywhere across Dandenong and the south-east, measure every wall including where it runs out of square, and talk through how you use the space. Then we draw a layout and help you choose door styles, finishes and a compliant benchtop, followed by a fixed written quote so you know the cost before anything is built.

Once you sign off, we build your cabinetry in the workshop to fine tolerances. Boxes are glued, dowelled and assembled dead square, using HMR moisture-resistant board in wet areas, heat-sealed edge-banding, and quality Blum or Hettich soft-close hardware rated well beyond 100,000 cycles. Building offsite means precision, quality control and far less disruption in your home.

We install on site, scribing and packing everything level to your real walls and setting reveals to within about 2mm even where the wall behind is not plumb. Natural stone benchtops are templated and fitted through licensed stonemasons. We finish by adjusting every hinge and drawer, cleaning up, and walking you through your new joinery. One local team from first measure to final drawer.
Cabinet refacing replaces every surface that is seen and every moving part, while keeping the carcasses. New doors, drawer fronts, exposed end panels and kickboards are made to measure, and handles, hinges and runners are replaced. The boxes, internal shelves, benchtop and plumbing stay in place, which is what removes most of the cost and most of the disruption. It changes how a kitchen looks and operates, but it cannot change the layout beyond what the existing openings allow.
Four checks decide it: whether the box is still square, whether the board is dry and sound particularly at the sink and dishwasher, whether the fixings into wall and floor are solid, and whether the openings are consistent enough for new fronts to sit with even reveals. Swelling at a sink-run base unit is the usual disqualifier, because a new door on a swollen box will never hang true. The sink cabinet is always checked first, since an unsealed carcass there deteriorates quietly over years. Where the boxes are unsound, replacement is recommended even though it is the larger job.
A reface typically costs under half a comparable full replacement. A modest kitchen reface in melamine or high-pressure laminate, covering doors, fronts, handles, hinges and runners, often runs from around $4,000 to $8,000, against a from-scratch custom kitchen starting well above that. Timber veneer fronts lift it to roughly $7,000 to $14,000 and sprayed two-pac to around $8,000 to $18,000, both still below a rebuild. The saving comes from keeping the carcasses, the benchtop and the plumbing where they are.
Finishes run from melamine and high-pressure laminate, which are the value choices and handle daily wear well, through timber veneer for real grain across the fronts, to sprayed two-pac polyurethane for the deepest finish. Two-pac can be colour-matched to an existing benchtop or splashback, which often decides it when only the fronts are changing. Profiles run from flat slab through shaker to handleless J-pull and finger-pull, and switching to a handleless profile changes the look more than a colour change does.
Allow around two to four weeks end to end. The assessment and measure takes about a week, fabrication of the new fronts runs one to two weeks in the workshop, and the install is usually one to two days on site. The kitchen stays usable for most of the install, which is the main practical advantage over a replacement. Adding a new benchtop extends it by roughly a week, because templating happens after the new fronts are fitted.
Yes. Vanity doors and drawer fronts are refaced the same way, with moisture-resistant substrates specified for the wet area, and robe doors and fronts can be replaced to the measured openings. Freestanding display cabinets and dressers are also repaired, covering loose joints, failed runners, broken hinges and damaged backs. Where a piece has furniture or sentimental value, repair is almost always the better answer than replacement.
GET A FREE QUOTE

BUSINESS
SERVICES
OPERATING HOURS
Sun: 7:00am - 9:00pm
Mon: 7:00am - 9:00pm
Tue: 7:00am - 9:00pm
Wed: 7:00am - 9:00pm
Thu: 7:00am - 9:00pm
Fri: 7:00am - 9:00pm
Sat: 7:00am - 9:00pm